Page 9 of 9

Re: Kinetic sculpture designed by Clayton Boyer

Posted: Wed Dec 16, 2020 7:57 am
by Aviv
Kineticrazy wrote: Dan,
  I noticed the bearing in the video was still shielded. It was suggested in another thread to remove the shields, soak and clean the bearings with mineral spirits and then soak and lubricate them with silicone. Do you go through the same process?

I was wondering if anyone has tried thrust bearings. I happened upon them when poking around the internet...here's an example..

https://www.amazon.com/51100-Thrust-Bearing-10x24x9-Bearings/dp/B002BBJSDG/ref=cm_cr_arp_d_product_top?ie=UTF8

Thanks,

Eric
For kinetic sculptures, that are not experiencing high loads (I think?), would it be valuable to wash the bearings in mineral spirits, to remove the lubrication in order to reduce friction, without lubricating back?
I know the lubrication is there for a reason, but it also adds friction, and maybe for the weights involved in kinetic sculptures this isn?t an issue?

Re: Kinetic sculpture designed by Clayton Boyer

Posted: Wed Dec 16, 2020 8:50 am
by ArtF
I'd agree with that, so long as it isn't wobbly.. the least resistance as possible is
desirable..

Re: Kinetic sculpture designed by Clayton Boyer

Posted: Sun Dec 20, 2020 8:34 am
by steve323
I have been testing various bearing configurations for pendulum supports. It is not exactly the same setup as a kinetic sculpture, but I believe some of the same principles apply. Less friction is better.

The load is around 8 ounces. I measure the time that it takes for the swing to degrade from +/-8 degrees to +/-1 degree.

Here are the swing times of various 623 (3x10x4mm) ball bearing configurations:
    5m 50s  sealed with factory grease intact
    7m 40s  shielded with factory grease intact
  14m 00s  shields removed and cleaned - low end of range
  20m 50s  shields removed and cleaned - high end of range
  24m 30s  shields removed and cleaned with Teflon dry lube added

The bearings were generic eBay versions costing around $5 for 10 bearings. 3 of the 10 were slightly tighter than the others. The remaining 7 would probably all last around 20 minutes or better.

My clock with ball bearings for the pendulum support has been running non-stop for two years with no signs of wear. Running then dry seems OK when the load is significantly lower than the rated max loads.

Steve

Re: Kinetic sculpture designed by Clayton Boyer

Posted: Sun Dec 20, 2020 10:16 am
by ArtF
>>24m 30s  shields removed and cleaned with Teflon dry lube added


Good god, thats way better than I figured on top of head. Thats a long time to degrade ..

Art

Re: Kinetic sculpture designed by Clayton Boyer

Posted: Sun Dec 20, 2020 11:24 am
by steve323
ArtF wrote: >>24m 30s  shields removed and cleaned with Teflon dry lube added


Good god, thats way better than I figured on top of head. Thats a long time to degrade ..

Art
It was much longer than I expected as well, especially since they were random no-name bearings.

A pendulum degrading in 24 minutes only needs 1/3 as much restoring force as an 8 minute pendulum. I hope to post a video soon showing the complete results.

Steve

Re: Kinetic sculpture designed by Clayton Boyer

Posted: Sun Dec 20, 2020 3:27 pm
by ArtF
Steve:

  Its all good to know. In future I know the way Ill go.. :)

Art

Re: Kinetic sculpture designed by Clayton Boyer

Posted: Mon Jun 28, 2021 3:54 am
by deraudrl
FWIW, I tried a couple with mineral spirits: the problem is they seemed to gum up a week or so later...some kind of residue attracting cruft in my garage. (The stuff they sell here in SoCal doesn't look/smell like the stuff I remember from my youth.)

"Gunk" engine cleaner worked a lot better, except for the hassle of getting it out of the aerosol can so I could really soak the bearings.

Re: Kinetic sculpture designed by Clayton Boyer

Posted: Sat Jul 17, 2021 3:33 am
by deraudrl
Finally completed my laser-cut acrylic take on 'Zinnia' after letting the plans and parts sit for almost five years...
Did some re-engineering, mostly to get all the parts to fit the 12"x16" limits of my laser. Wheels are 20", which is about as big as I can segment one up without a ton of waste.
Short video of it in operation here: https://www.dropbox.com/s/fgyz2qq84whfc ... 9.mp4?dl=0
20210716_124831.jpg

Re: Kinetic sculpture designed by Clayton Boyer

Posted: Sat Jul 17, 2021 3:42 am
by ArtF
Excellent. Nice pattern.

Art

Test, just a test

Posted: Tue Aug 17, 2021 6:52 am
by XRumerTest
Hello. And Bye.

Re: Kinetic sculpture designed by Clayton Boyer

Posted: Tue Aug 17, 2021 11:21 am
by ArtF
works fine. :)